Mechanical Contractor means a contractor whose services are unlimited in the execution of contracts requiring the experience, knowledge, and skill to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, central air-conditioning, refrigeration, heating, and ventilating systems.
This includes duct work in connection with a complete system only to the extent such duct work is performed by the contractor as is necessary to make complete an air-distribution system, boiler and unfired pressure vessel systems, lift station equipment and piping, and all appurtenances, apparatus, or equipment used in connection therewith, and any duct cleaning and equipment sanitizing which requires at least a partial disassembling of the system; to install, maintain, repair, fabricate, alter, extend, or design, when not prohibited by law, piping, insulation of pipes, vessels and ducts, pressure and process piping, pneumatic control piping, gasoline tanks and pump installations and piping for same, standpipes, air piping, vacuum line piping, oxygen lines, nitrous oxide piping, ink and chemical lines, fuel transmission lines, liquefied petroleum gas lines within buildings, and natural gas fuel lines within buildings; to replace, disconnect, or reconnect power wiring on the load side of the dedicated existing electrical disconnect switch; to install, disconnect, and reconnect low voltage heating, ventilating, and air-conditioning control wiring; and to install a condensate drain from an air-conditioning unit to an existing safe waste or other approved disposal other than a direct connection to a sanitary system. The scope of work for such contractor shall also include any excavation work incidental thereto, but shall not include any work such as potable water lines or connections thereto, sanitary sewer lines, swimming pool piping and filters, or electrical power wiring.
To apply, contact State of Florida Department of Business and Professional Regulation 1-850-487-1395.
If applying for initial licensure from May 1st of an Even numbered year through August 31st of an Odd numbered year the fee is $249.
If applying for initial licensure from September 1st of an Odd numbered year through April 30th of an Even numbered year the fee is $149.
You must pay a fee of $56.25 to Promissor/Pearson VUE for the processing of your electronic fingerprints.
Candidates will receive an unofficial grade report on the day they pass the exam. However, test scores and license approval do not become official until ratified by the Contractors Licensing Board at their next meeting. Licenses are typically received within 14 days of the exam.
Important Contacts
Florida does not have a reciprocal agreement with any other states for the Mechanical license.
As of this time Florida requires 14 hours of board approved continuing education each biennium prior to the renewal period for both certified and registered contractors. At least 1 hour must deal with workplace safety, 1 hour must be on the subject of workerโs compensation, 1 hour must cover the subject of business practices, 1hour must cover the subject of laws and rules, 1 hour must cover wind mitigation methodologies, and 1 hour must cover the Florida Building Code advanced modules.
All parts of the examination:
Pay $135.00 examination development fee payable to PTI, $80.00 examination administration fee payable to DBPR, but mailed to PTI. An $80.00 examination administration fee payable to Pearson Vue (formerly Promissor), the CBT (Computer Based Testing) contracted vendor, is due at the time of scheduling.
- A score of at least 70% is required to pass the exams.
- The exam is 2 days, open book, multiple-choice, and timed.
- There are 2 parts to the exam, the business finance part and trade knowledge. The time limit for the trade exam is 4 hours and 45 minutes. The Business Finance portion is 6.5 hrs.
- The exams are computer based and offered throughout the year at PearsonVue Testing Facility. Exams are on a first come first serve basis.
You must complete all portions of the examination within 4 years of the first attempt. After four years, all previous test scores become invalid and you will be required to take all parts of the examination again.
- The Florida Mechanical exam is held during the 2nd day with a morning session of 65 equally weighted questions and an afternoon session of 65 equally weighted questions. The scores for the 2 sessions will be combined to determine your score for this portion of the exam.
- The Florida Business and Finance exam is a 6.5 hr exam consisting of 125 equally weighted questions.
- Applicants must submit an application and exam fee to become registered to take the exam. The testing company must receive completed applications and appropriate fees no later than 30 days prior to the next scheduled exam date.
-
Topics covered on the trade knowledge exam portion are pre-installation and design engineering, ductwork and HVAC materials, installation of refrigeration and HVAC systems, installation of mechanical systems, installation of refrigeration and HVAC equipment and components, installation of mechanical equipment and components, maintenance analysis of refrigeration and HVAC, maintenance service of refrigeration and HVAC, safety and equipment, and excavating.
- To schedule your exam you must contact Professional Testing, Inc (PTI) at 1-407-264-0562.
American Contractors offers a 5-day seminar to prepare for the Florida Mechanical contractor license exam and includes preparation for the Business and Finance exam. Please contact us for additional information, 1-800-992-1910.
